Guangzhou Tinci Materials Technology Co., Ltd.

Tinci's master range of lithium-ion battery electrolytes, covering 3C digital and power tool, power battery, energy storage and new material system electrolytes, supported by self-produced electrolyte salts and additives, and applied in new energy vehicles, digital products and energy storage.

Classified by application into 3C and power tools / power / energy storage / new material system; supports 4.2-4.85 V voltage systems and prismatic, pouch and cylindrical cells.

• Power batteries for new energy vehicles
• 3C digital and power tool batteries
• Energy storage batteries
• New material system (5 V LNMO etc.) batteries

Electrolyte series for 3C digital devices, emergency start units, drones, model aircraft, e-cigarettes and cylindrical power tool batteries, balancing high and low temperature performance, long cycle life and fast charging or high-rate discharge.

Applicable cathode systems: LCO 4.2-4.5 V / NMC 4.2-4.35 V; Matching anode: graphite / silicon-carbon; Conductivity: >= 9.0 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Density: 1.20-1.26 g/cm³ at 25 °C; Colour: <= 50 APHA; Storage temperature: <= 25 °C under dry argon

• 3C digital product batteries
• Drone, model aircraft and e-cigarette batteries
• Power tool batteries

Electrolyte series for traction batteries in electric two-wheelers, passenger cars and buses, offering long cycle life, balanced high and low temperature performance and fast charging capability.

Applicable cathodes: LFP / LMO / NMC / 5 V LNMO / LMFP; Matching anodes: graphite / silicon / LTO; Conductivity: >= 8.5 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Density: 1.20-1.28 g/cm³ at 25 °C; Flash point: >= 25 °C; Cell formats: prismatic / pouch / cylindrical

• Electric two-wheelers
• New energy passenger cars
• New energy buses

Electrolyte series for telecom base station and grid energy storage, balancing high and low temperature performance, low cost and long cycle life.

Applicable cathodes: LFP / LMFP / NMC; Matching anode: graphite; Conductivity: >= 8.0 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Density: 1.20-1.28 g/cm³ at 25 °C; Cell formats: prismatic / pouch; Designed cycle life: >= 6000 cycles; Storage temperature: <= 25 °C under argon

• Telecom base station energy storage
• Grid power-type energy storage
• Long-cycle energy storage systems

Development-stage electrolytes for high-voltage lithium nickel manganese oxide (LNMO) and other new material systems, featuring long room-temperature and high-temperature cycling plus good safety performance.

Applicable cathode: lithium nickel manganese oxide LNMO with 4.70-4.85 V cut-off; Matching anode: graphite; Conductivity: >= 7.5 mS/cm at 25 °C; Oxidation stability window: >= 4.9 V; Moisture: <= 15 ppm; Acid value (as HF): <= 40 ppm; Cell formats: prismatic / pouch; Storage temperature: <= 25 °C under dry argon

• 5 V high-voltage lithium-ion batteries
• High energy density batteries

Tinci's self-produced electrolyte salts and functional additives, which lower electrolyte cost and improve conductivity, thermal stability and cycle life.

Range: LiPF6 / LiFSI / NaPF6 lithium and sodium electrolyte salts plus VC, FEC and DTD additives; Purity: >= 99.9 %; Moisture: <= 20 ppm; Free acid (as HF): <= 100 ppm; Insolubles: <= 200 ppm; Metallic impurities: Fe / K / Na <= 1 ppm each; Delivery form: solid / EMC-DMC concentrate; Storage temperature: <= 25 °C under dry argon

• Lithium-ion battery electrolytes
• Sodium-ion battery electrolytes
• Electrolyte formulation additives

Main electrolyte salt for lithium-ion battery electrolytes; Tinci's lithium hexafluorophosphate EMC/DMC concentrate offers low cost and low impurity content.

CAS No.: 21324-40-3; supplied in EMC/DMC concentrate form.

• Lithium-ion battery electrolytes

Electrolyte salt for sodium-ion battery electrolytes, with low cost and excellent overall performance.

CAS No.: 21324-39-3; electrolyte salt for sodium-ion batteries.

• Sodium-ion battery electrolytes

Lithium-ion battery electrolyte additive and salt with high conductivity and good thermal stability that reduces impedance and improves cycling performance.

CAS No.: 171611-11-3; supplied as EMC/DMC concentrate.

• Lithium-ion battery electrolytes
• High-voltage and high-rate batteries

Lithium-ion electrolyte additive that lowers battery impedance and extends cycle life.

CAS No.: 678966-16-0; lithium-ion battery electrolyte additive.

• Lithium-ion battery electrolytes

Lithium-ion electrolyte additive that lowers battery impedance and improves cycle life.

CAS No.: 409071-16-5; lithium-ion battery electrolyte additive.

• Lithium-ion battery electrolytes

Lithium-ion battery electrolyte additive that lowers impedance and improves high-temperature storage and cycle life.

CAS No.: 643-080-8; lithium-ion battery electrolyte additive.

• Lithium-ion battery electrolytes

Lithium-ion battery electrolyte additive that lowers battery impedance and extends cycle life.

CAS No.: 1072-53-3; lithium-ion battery additive.

• Lithium-ion battery electrolytes

Lithium-ion battery additive that lowers battery impedance and improves cycle life.

CAS No.: 10497-05-9; lithium-ion battery additive.

• Lithium-ion battery electrolytes

Tinci's master range of sodium-ion battery electrolytes, based on layered oxide, Prussian blue or white or polyanion cathodes with hard carbon anodes, offering low cost and high safety.

Main electrolyte salt: NaPF6 / NaClO4; Applicable cathodes: layered oxide / Prussian blue (white) / polyanionic; Matching anode: hard carbon; Conductivity: >= 6.5 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Cell formats: prismatic / cylindrical / pouch; Application temperature range: -40 °C to +60 °C

• Sodium-ion batteries for energy storage
• Sodium-ion batteries for low-speed vehicles

Sodium-ion battery electrolytes for energy storage applications, featuring low cost and long cycle life.

Main electrolyte salt: NaPF6 / NaClO4; Applicable cathodes: layered oxide / Prussian blue (white) / polyanionic; Matching anode: hard carbon; Conductivity: >= 6.0 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Cell formats: prismatic / pouch; Designed cycle life: >= 4000 cycles; Storage temperature: <= 25 °C

• Sodium-ion batteries for energy storage

Sodium-ion battery electrolytes for low-speed vehicles, combining low cost, high power and balanced high and low temperature performance.

Main electrolyte salt: NaPF6 / NaClO4; Applicable cathodes: layered oxide / Prussian blue (white) / polyanionic; Matching anode: hard carbon; Conductivity: >= 7.0 mS/cm at 25 °C; Moisture: <= 20 ppm; Acid value (as HF): <= 50 ppm; Cell formats: prismatic / cylindrical; Application temperature range: -20 °C to +55 °C; Storage temperature: <= 25 °C

• Low-speed electric vehicles
• Two- and three-wheel low-speed vehicles

Master range of solid-state electrolytes for high-nickel, high-voltage and lithium-metal anode batteries, offering high energy density, high power density and high safety.

Electrolyte type: oxide / sulfide / polymer composite solid-state electrolyte; Ionic conductivity: 0.5-5 mS/cm at 25 °C; Electrochemical stability window: >= 4.5 V; Lithium-ion transference number: >= 0.6; Membrane thickness: 20-50 µm; Matching anode: lithium metal / silicon-carbon; Test temperature: 25 °C to 80 °C; Storage humidity: <= 1 % RH

• Solid-state and semi-solid lithium batteries
• High energy density power batteries

Tinci solid-state electrolyte products suitable for high-nickel, high-voltage and lithium-metal anode batteries, with high energy density, high power density and high safety.

Product form: solid-state / semi-solid electrolyte; Ionic conductivity: 1.0-5 mS/cm at 25 °C; Electrochemical stability window: >= 4.8 V; Lithium-ion transference number: >= 0.65; Applicable cathodes: high-nickel NMC / high-voltage systems; Matching anodes: lithium metal / silicon-carbon; Cell formats: prismatic / pouch; Storage humidity: <= 1 % RH

• Solid-state batteries
• High-safety power batteries

Tinci cathode materials and precursors, including lithium iron phosphate cathode material and iron phosphate precursor, forming an integrated advantage together with electrolytes.

Cathode material: lithium iron phosphate LFP; Specific capacity: >= 155 mAh/g at 0.1 C; Initial coulombic efficiency: >= 95 %; Compacted density: >= 2.4 g/cm³; Particle size: D50 1.5-3.0 µm; Cycle life: >= 3000 cycles at 80 % SOH; Moisture: <= 500 ppm; Iron phosphate precursor: Fe/P ratio 0.96-1.02

• Lithium-ion battery cathodes
• LFP power batteries
• Energy storage batteries

Tinci's new energy binder and adhesive business, covering electrode binders, edge-coating adhesives and silicone or polyurethane adhesive systems for power battery assembly and thermal management.

Product range: PVDF cathode binder / SBR-CMC anode binder / edge-coating adhesive / silicone adhesive / polyurethane structural, thermal conductive and potting adhesives; Viscosity: 500-50000 mPa·s at 25 °C; Solids content: 15-60 %; Density: 0.95-1.60 g/cm³; Lap shear strength: >= 5 MPa; Thermal conductivity: 0.5-3.0 W/(m·K); Service temperature: -40 °C to +150 °C; Shelf life: 6-12 months

• Power battery cell manufacturing
• Battery pack assembly and thermal management
• Energy storage and electronics bonding and sealing

Binder series for lithium battery cathodes that improves adhesion, dispersion and electrochemical stability, suitable for LFP, LCO, NCM and sodium-ion systems.

TC-BP201 white or slightly yellow powder, 15 kg/drum; Tinctive T129 brown-yellow liquid, 60/200 kg/drum; T126 golden transparent viscous liquid, 25/200 kg/drum; P series white or slightly yellow powder, 15 kg/drum.

• LFP cathodes
• LCO and NCM cathodes
• Sodium-ion battery cathodes

Binder series for graphite and silicon-based anodes with strong adhesion and low electrolyte swelling, capable of partially or fully replacing CMC/SBR.

K119 gel-like liquid, 60/200 kg/drum; E300 slightly yellow liquid, 60/180 kg/drum; E248 milky white or slightly yellow emulsion, 60/180 kg/drum.

• 3C and power graphite anodes
• Silicon-based anodes
• High energy density anodes

Adhesive series for electrode edge coating and separator bonding, with ultra-high adhesion and excellent electrolyte resistance.

B125 milky white or slightly yellow emulsion, 25/200 kg/drum; B126M and B126P golden viscous liquid, 25 kg/drum; B127 series, 25 kg/drum; B128 golden viscous liquid, 25 kg/drum.

• Anode and silicon-based electrode edge coating
• Cathode tab insulating coating
• Separator bonding

Silicone-based new energy adhesives covering bonding and sealing, thermally conductive potting, thermal gels, foam sheets and insulation elastomers for power battery thermal management.

Representative grades: TCR-1791 / TCS-1600LD1 / TCS-270 / TCS-CG / TCS-1030 / TCS-260R; Viscosity: 3000-60000 mPa·s at 25 °C; Thermal conductivity: 1.0-3.0 W/(m·K); Density: 1.4-2.2 g/cm³; Dielectric strength: >= 18 kV/mm; Volume resistivity: >= 1.0 x 10^14 Ω·cm; Flammability rating: UL94 V-0; Service temperature: -40 °C to +200 °C

• Power battery BMS potting
• Cell module heat conduction and dissipation
• Battery component damping and thermal insulation

Silicone adhesives that are flame retardant and provide good bonding and sealing, used for bonding and sealing various electronic components.

TCR-1791FM thermal conductivity 0.8 W/m.K, thixotropic paste; FG and F are semi-flowing and semi-thixotropic; 300 mL/cartridge, 2.6 L/cartridge, 20 kg/drum.

• Electronic component bonding and sealing
• Battery pack component sealing

Low specific gravity, lightweight silicone potting compounds with high thermal conductivity and V0 flame retardancy, used for thermally conductive potting and insulation protection of power battery BMS systems.

Thermal conductivity 0.8-3.0 W/m.K, low viscosity and self-leveling; 10 kg/drum, 20 kg/drum.

• Power battery BMS potting
• Power module heat dissipation and fire protection

Silicone thermal gels that are soft and exert gentle stress, used to fill the gap between cell modules and liquid cooling plates for heat conduction.

Thermal conductivity 1.0-4.0 W/m.K, V0 flame retardant; 20 kg/drum.

• Heat conduction between cell modules and liquid cooling plates
• Insulation protection

Low-density molded silicone foam sheets used for damping, cushioning, insulation and thermal insulation of power battery components.

Available in black, gray, white and other colors; 20 kg/box.

• Power battery component damping and cushioning
• Insulation and thermal insulation

Low-density, low-viscosity silicone thermal insulation elastomers used for filling, damping, cushioning, insulation and thermal insulation of module cells.

Gray or white fluid; 15 kg/drum.

• Cell filling and thermal insulation
• Module insulation protection

Polyurethane-based new energy adhesives covering structural adhesives, thermally conductive structural adhesives, thermal adhesives, sealants, foaming adhesives, insulating materials and potting compounds for battery pack structural bonding and thermal management.

Includes Bondway 3112/8815/8825 structural adhesives, 3920L/3912LD/8867 thermally conductive structural adhesives, 9151/9020 thermal adhesives, 626C series sealants, 9263-20 foaming adhesive, P1260-4 insulation and 3520LS potting compounds; 400 mL cartridge, 20 L/drum, 210 L/drum.

• Cell to enclosure or water cooling plate bonding
• Battery pack sealing and insulation
• Thermally conductive potting

Structural bonding adhesives for battery packs, used for bonding cells to the enclosure and cells to cells, side plates or end plates.

Chemistry: polyurethane structural adhesive; Viscosity: 20000-60000 mPa·s at 25 °C; Lap shear strength: >= 8 MPa; Tensile strength: >= 10 MPa; Elongation at break: >= 50 %; Shore hardness: 60-80 A; Density: 1.3-1.6 g/cm³; Service temperature: -40 °C to +85 °C; Pack sizes: 400 mL cartridge / 20 L pail / 210 L drum

• Cell to enclosure bonding
• Cell to cell, side plate or end plate bonding

Adhesives combining thermal conductivity and structural strength, used for bonding cells to the enclosure and to liquid cooling plates, including energy storage projects.

Chemistry: polyurethane thermally conductive structural adhesive; Viscosity: 15000-50000 mPa·s at 25 °C; Thermal conductivity: 1.0-2.0 W/(m·K); Lap shear strength: >= 6 MPa; Tensile strength: >= 8 MPa; Dielectric strength: >= 15 kV/mm; Service temperature: -40 °C to +85 °C; Pack sizes: 400 mL cartridge / 20 L pail / 210 L drum

• Cell to enclosure bonding (energy storage)
• Cell to liquid cooling plate bonding

Thermally conductive bonding and potting adhesives for thermally conductive bonding of cells to enclosures, housings, side plates and bottom cases.

Chemistry: polyurethane thermally conductive adhesive; Viscosity: 8000-40000 mPa·s at 25 °C; Thermal conductivity: 1.2-3.0 W/(m·K); Density: 1.6-2.4 g/cm³; Lap shear strength: >= 5 MPa; Dielectric strength: >= 15 kV/mm; Service temperature: -40 °C to +120 °C; Pack sizes: 400 mL cartridge / 20 L pail / 210 L drum

• Cell to enclosure heat conduction
• Cell bonding to housing, side plate or bottom case

Sealants for battery pack metal structures, used for aluminium-to-aluminium and aluminium-to-steel bonding.

Chemistry: polyurethane sealant; Substrates: 3003Al / 6061Al / e-coated steel / powder-coated aluminium; Viscosity: 20000-60000 mPa·s at 25 °C; Lap shear strength: >= 6 MPa; Shore hardness: 50-70 A; Damp-heat resistance: >= 1000 h at 85 °C / 85 % RH; Service temperature: -40 °C to +90 °C; Pack sizes: 300 mL cartridge / 20 L pail / 210 L drum

• 3003Al to 3003Al bonding
• 6061Al to electrophoretic steel or powder-coated aluminium bonding

Foaming filler adhesive used for foam filling between cells and the housing and between tabs and the housing.

Chemistry: polyurethane foaming adhesive; Expansion ratio: 2-4 times; Tack-free time: <= 20 min at 25 °C; Cured density: 0.3-0.6 g/cm³; Compressive strength: >= 1 MPa; Initial viscosity: 5000-30000 mPa·s at 25 °C; Service temperature: -40 °C to +85 °C; Pack sizes: 20 L pail / 210 L drum

• Cell to housing foam filling
• Tab to housing foam filling

Insulation treatment material for the interior of battery packs, used for insulating cells, side plates, end plates and module housings.

Material type: polyurethane battery pack insulation material; Dielectric strength: >= 20 kV/mm; Volume resistivity: >= 1.0 x 10^14 Ω·cm; Withstand voltage: >= 3000 V AC for 1 min; Flammability rating: UL94 V-0; Breakdown voltage: >= 15 kV; Service temperature: -40 °C to +120 °C; Pack size: 20 kg per carton

• Cell, side plate, end plate and module housing insulation

Thermally conductive potting compounds for thermally conductive potting of cells and housings.

Chemistry: polyurethane thermally conductive potting compound; Viscosity: 3000-20000 mPa·s at 25 °C; Thermal conductivity: 1.0-2.5 W/(m·K); Shore hardness: 40-70 A; Volume resistivity: >= 1.0 x 10^13 Ω·cm; Flammability rating: UL94 V-0; Service temperature: -40 °C to +120 °C; Pack sizes: 400 mL cartridge / 20 L pail / 210 L drum

• Cell to housing thermally conductive potting

Bonding and thermal management material solutions for automotive electronics that ensure driving safety and system stability.

Material range: automotive-grade adhesives / thermal interface materials / potting compounds; Thermal conductivity: 1.0-5.0 W/(m·K); Thermal resistance: <= 0.5 K·cm²/W; Dielectric strength: >= 15 kV/mm; Flammability rating: UL94 V-0; Damp-heat resistance: >= 1000 h at 85 °C / 85 % RH; Service temperature: -40 °C to +150 °C; Storage life: 6-12 months at <= 25 °C

• Automotive electronics assembly
• Automotive electronics heat conduction and bonding

Integrated solution of high-performance PEEK engineering plastics and professional adhesives for intelligent robots.

Material range: PEEK engineering plastic combined with structural adhesives; Tensile strength: >= 100 MPa; Flexural strength: >= 150 MPa; Density: 1.30-1.45 g/cm³; Heat deflection temperature: >= 160 °C; Continuous service temperature: <= 250 °C; Flammability rating: UL94 V-0; Coefficient of friction: <= 0.35

• Intelligent robot assembly
• Robot structural bonding

Highly durable, UV-resistant encapsulation and sealing materials for solar photovoltaic modules that extend outdoor service life.

Material range: photovoltaic encapsulant films (EVA / POE) and frame sealants; Light transmittance: >= 91 % from 380 to 1100 nm; Tensile strength: >= 15 MPa; Elongation at break: >= 500 %; Degree of crosslinking: 75-90 %; Shrinkage: <= 2 % at 150 °C for 30 min; UV ageing: >= 3000 h with delta YI <= 3; Service temperature: -40 °C to +85 °C

• Photovoltaic module encapsulation
• Photovoltaic frame sealing

High-purity, low-stress advanced electronic materials for semiconductor manufacturing and packaging that meet the demanding requirements of chip processes.

Material range: high-purity electronic grade chemicals and moulding / packaging materials; Chemical purity: >= 99.999 % (5N); Metallic impurities: <= 10 ppb; Particles of 0.1 µm and above: <= 50 per mL; Glass transition temperature: >= 150 °C; Coefficient of thermal expansion: <= 20 ppm/K; Cure shrinkage: <= 0.3 %; Applicable process temperature: <= 260 °C for reflow

• Semiconductor manufacturing
• Chip packaging

One-stop consumer electronics adhesive solution covering bonding, heat conduction, sealing and potting, enabling thin, lightweight and highly reliable assembly of smart terminals.

Material range: consumer electronics bonding / thermal / sealing / potting adhesives; Viscosity: 1000-50000 mPa·s at 25 °C; Thermal conductivity: 1.0-4.0 W/(m·K); Lap shear strength: >= 5 MPa; Dielectric strength: >= 15 kV/mm; Curing time: <= 30 min for initial cure at 25 °C; Service temperature: -40 °C to +125 °C; Shelf life: 12 months

• Smartphone and terminal assembly
• Consumer electronics heat conduction and sealing

Guangzhou Tinci provides adhesive and protective material solutions for non-lithium sectors such as construction, home decoration, transportation and power, helping customers extend service life of components and maintain reliable operation even in demanding environments.

Construction, home decoration, transportation and power industries; adhesives, sealants and insulation protection materials; functions of bonding, sealing, insulation, weather resistance and durability

• Construction engineering
• Home decoration
• Transportation
• Power insulation protection

Rheology modifiers for personal care such as carbomers, giving O/W creams a moisturizing skin feel and suitable for formulations containing surfactants.

INCI: acrylates/C10-30 alkyl acrylate crosspolymer; representative grades TC-CARBOMER FD20/FD2010/FD2020.

• Personal care creams
• Shampoos and body washes
• Skin care products

Amino acid and amphoteric mild surfactant series that is gentle, readily biodegradable, foaming and foam-stabilizing, antibacterial and eco-friendly, used in personal and home care.

Product category: amino acid and amphoteric surfactants; Active matter content: 30-50 %; pH of 1 % aqueous solution: 5.0-8.0; Viscosity: 500-5000 mPa·s at 25 °C; Surface tension: <= 35 mN/m; Sodium chloride: <= 0.5 %; Colour: <= 100 APHA; Biodegradability: >= 90 %; Shelf life: 24 months

• Personal care cleansing
• Home care
• Hair care products

Taurate (taurine and isethionate) surfactant series with excellent foaming and fine, dense lather, readily biodegradable and safe to use.

Product name: taurate / isethionate surfactants; Active matter content: >= 30 %; pH of 1 % aqueous solution: 5.5-7.5; Foam height: >= 150 mm by Ross-Miles at 0.1 %; Surface tension: <= 32 mN/m; Sodium chloride: <= 0.3 %; Biodegradability: >= 95 %; Shelf life: 24 months

• Facial cleansers
• Cleansing bars
• Shampoos
• Body washes

Various silicone oils classified by chemical structure (volatile, linear, polyether-modified, amino, phenyl and alkyl-modified), used for sensory modification and conditioning in personal care.

Product category: volatile / linear / polyether as well as amino, phenyl and alkyl modified silicone oils; Viscosity: 5-100000 cSt at 25 °C; Density: 0.93-1.07 g/cm³; Refractive index: 1.390-1.450; Volatile content: <= 1.0 % at 150 °C for 2 h; Flash point: >= 200 °C; Pour point: <= -50 °C; Shelf life: 24 months

• Personal care products
• Toners, masks and creams
• Color cosmetics

Silicone-based skin feel modifiers including elastomer gels, silicone waxes and MQ resin film formers that enhance the moisturizing effect and long-lasting performance of skin care and color cosmetics.

Silicone elastomers are high-molecular-weight crosslinked compounds; MQ resin film formers form breathable films.

• Skin care
• Color cosmetics
• Sun protection

Personal care emulsifiers; the AQUAGEL series provides thickening with a fresh feel, while silicone emulsifiers offer W/O and W/Si emulsification and can be processed either hot or cold.

Product category: polyoxyethylene-modified silicone personal care emulsifiers; HLB value: 3-12; Viscosity: 200-5000 mPa·s at 25 °C; pH of 1 % aqueous solution: 5.0-7.0; Emulsion particle size: <= 5 µm; Recommended dosage: 1-5 %; Processing: cold or hot process; Shelf life: 24 months

• Skin care creams
• Hair care products
• Color cosmetic emulsification

Cationic conditioning agents that repair split ends, improve softness and antistatic performance, and enhance a silky smooth feel in skin care.

Product category: cationic cellulose / cationic guar / cationic synthetic polymer conditioning agents; Solids content: >= 95 %; Nitrogen content: 0.8-2.0 %; Viscosity of 1 % aqueous solution: 1000-5000 mPa·s; pH of 1 % aqueous solution: 4.0-7.0; Ash content: <= 1.0 %; Recommended dosage: 0.2-1.0 %; Shelf life: 24 months

• Hair washing and care
• Skin care
• Personal care

Acrylic crosslinked copolymer rheology modifiers that suspend, thicken and stabilize, with salt tolerance and good compatibility with surfactants.

Chemistry: crosslinked acrylic (ester) copolymer; Solids content: >= 30 %; Viscosity of 1 % aqueous solution: 3000-20000 mPa·s; pH of 1 % aqueous solution: 2.5-4.5; Light transmittance: >= 85 %; Salt tolerance: stable with NaCl >= 2 %; Density: 1.05-1.15 g/cm³; Recommended dosage: 0.5-2.0 %; Shelf life: 24 months

• Shampoos
• Body washes
• Foundation creams
• Sunscreens

Derivatives sourced from natural glucose that are mild and can act as thickeners, humectants and cationic conditioning agents.

Raw material origin: natural glucose derivatives (GLUCO series); Active matter content: 50-60 %; pH of 1 % aqueous solution: 11.0-12.5; Free alcohol: <= 1.0 %; Viscosity at 25 °C: 1000-4000 mPa·s; HLB value: 11-14; Colour: <= 100 APHA; Biodegradability: >= 95 %; Shelf life: 24 months

• Personal care
• Gentle cleansing
• Moisturizing and conditioning

Hydroxyethylidene diphosphonic acid organic polyphosphate chelating agent that forms stable complexes with metal ions and acts as a complexing agent and water stabilizer.

Chemistry: organic polyphosphonic chelating agent based on hydroxyethylidene diphosphonic acid; Active matter content: >= 45 %; Chelating value as CaCO3: >= 300 mg/g; pH of 1 % aqueous solution: <= 2.0; Density: 1.30-1.45 g/cm³; Iron content: <= 20 ppm; Applicable pH range: 3-12; Thermal stability: <= 100 °C; Shelf life: 24 months

• Personal care products
• Anti-dandruff shampoos

Amino acid-based cationic surfactants made from L-arginine, with strong antibacterial activity, high safety and excellent biodegradability.

Raw material origin: natural green preservative derived from the amino acid L-arginine; Active matter content: >= 95 %; pH of 1 % aqueous solution: 5.0-7.0; Minimum inhibitory concentration: <= 0.5 %; Applicable pH range: 4-8; Recommended dosage: 0.5-2.0 %; Biodegradability: >= 90 %; Shelf life: 24 months

• Food
• Cosmetic preservation

Sunscreen agent product series suitable for different formulation systems with excellent safety.

Product category: multi-system sunscreen agents; UV absorption peaks: 280-380 nm; SPF contribution: >= 30 at 10 % dosage; UVA/UVB protection ratio: >= 0.6; Purity: >= 98 %; Loss on drying: <= 0.5 %; Recommended dosage: 2-10 %; Heat resistance: <= 80 °C; Shelf life: 36 months

• Sun protection skin care
• Sun protection in color cosmetics

Silicone elastomer gel skin feel modifier for color cosmetics that delivers a velvety skin feel.

Product category: silicone elastomer gel skin-feel modifier; Carrier: volatile silicone oil >= 80 %; Non-volatile content: 15-25 %; Viscosity: 200000-800000 mPa·s at 25 °C; Refractive index: 1.39-1.42; Density: 0.95-1.05 g/cm³; Thixotropic index: >= 2.0; Recommended dosage: 3-20 %; Shelf life: 24 months

• Liquid foundation
• Makeup primer
• Velvet lipstick and lip glaze
• Elastic and mousse eye shadow

Emulsifiers for color cosmetics that stabilize the emulsion system.

Emulsion type: W/O and W/Si cosmetic emulsifiers; HLB value: 3-8; Viscosity: 200-5000 mPa·s at 25 °C; Emulsion particle size: <= 3 µm; Heat stability: no phase separation at 45 °C for 30 days; Processing temperature range: -15 °C to +50 °C; Recommended dosage: 2-6 %; Shelf life: 24 months

• Liquid foundation
• Sun protection
• Makeup primer
• Emulsified lip glaze
• Mousse eye shadow

Carbomer-type thickeners for color cosmetics that provide system viscosity and stability.

Chemistry: carbomer crosslinked polyacrylic acid thickener; Solids content: >= 98 %; Viscosity of 0.5 % aqueous solution after neutralisation: 15000-45000 mPa·s; pH of 1 % aqueous solution: 2.5-3.5; Carboxyl content: 56-68 %; Residual benzene: <= 2 ppm; Loss on drying: <= 2.0 %; Recommended dosage: 0.2-1.0 %; Shelf life: 36 months

• Color cosmetic pastes
• Emulsions and gels

Film formers for color cosmetics that improve makeup durability and resistance to transfer.

Product category: cosmetic film-forming resin with non-volatile content 40-55 %; Minimum film-forming temperature: <= 25 °C; Glass transition temperature: 20-60 °C; Water-resistant wear time: >= 8 h; Viscosity: 1000-10000 mPa·s at 25 °C; Recommended dosage: 3-10 %; Applicable pH range: 5-9; Shelf life: 24 months

• Color cosmetics
• Sun protection
• Lip products

Amino acid surfactants for home cleaning and pet care, mild and readily biodegradable.

Product category: amino acid surfactants for home care and pet care; Active matter content: 30-40 %; pH of 1 % aqueous solution: 7.0-9.0; Surface tension: <= 30 mN/m; Sodium chloride: <= 0.5 %; Detergency ratio: >= 1.0 by national standard method; Biodegradability: >= 95 %; Recommended dosage: 2-15 %; Shelf life: 24 months

• Home hard surface cleaning
• Pet care
• Dishwashing and laundry

Amphoteric mild surfactants for home and pet care that are gentle and non-irritating with good detergency and foaming.

Product category: mild amphoteric surfactants for home care and pet care (betaine / imidazoline / amine oxide); Active matter content: 30-35 %; pH of 1 % aqueous solution: 6.0-8.0; Sodium chloride: <= 5.0 %; Free amine: <= 0.5 %; Surface tension: <= 35 mN/m; Foam height: >= 140 mm; Recommended dosage: 2-20 %; Shelf life: 24 months

• Home cleaning
• Pet care

Conditioning agents for home and pet care that improve the after-wash feel.

Product category: cationic / polymeric conditioning agents for home care and pet care; Solids content: 20-40 %; pH of 1 % aqueous solution: 4.0-7.0; Viscosity: <= 5000 mPa·s at 25 °C; Ionic type: cationic; Density: 1.00-1.15 g/cm³; Recommended dosage: 0.5-3.0 %; Application temperature: 5 °C to 60 °C; Shelf life: 24 months

• Pet washing and care
• Home fabric care

Thickeners for home and pet care that adjust system viscosity.

Chemistry: acrylic rheology modifier / thickening polymer; Solids content: >= 30 %; Viscosity of 1 % aqueous solution: 5000-30000 mPa·s; pH of 1 % aqueous solution: 5.0-7.0; NaCl thickening response: >= 20000 mPa·s with 1 % NaCl; Density: 1.05-1.15 g/cm³; Recommended dosage: 0.5-3.0 %; Shelf life: 24 months

• Home cleaning
• Pet care